Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” 1 case – 2 rolls 5″ X 100′ rolls/case, 2 rolls total of vulcanized butyl COVER tape used to seal flat roof top areas, perimeter edge termination detail and other FLAT EPDM roof joints. NOT TO BE USED FOR FLASHING DETAIL! THIS PRODUCT IS COMPRISED OF CURED EPDM RUBBER LAMINATED TO UNCURED BUTYL TAPE. Need to use primer activator to prime the flat area before applying the 5″ cover tape. This is 1 case, 2 ROLLS – 5″ x 100′ rolls cover case, 2 rolls total and weighs 48 lbs per case Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, PayPal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable.Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricingWe currently only ship to the lower 48 sates, not Alaska or Hawaii
1 case – 2 – rolls 6″ x 100′ EPDM Rubber Flashing tape P-S THE LOTTES COMPANIES
Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” FREE SHIPPING 48 STATES 1 cases – 2 rolls 6″ x 100′ rolls/case of vulcanized butyl flashing tape used to seal flash around roof top detail projections overlapping pieces of EPDM deck sheet roofing to form a watertight seal. Need to use primer activator to prime the seam area before applying the 6″ flashing tape. SELF VULCANIZING FLASHING JOINTS All FLASHING DETAIL: shall be sealed using 6″ OR 12″ SELF VULCANIZING FLASHING TAPE. All joints shall be shingled to shed water toward the drains, scuppers, etc. Contact surfaces for the FLASHING TAPE shall be cleaned to remove construction dirt using a light application of unleaded gas on a clean, lint-free rag. After cleaning apply primer to surfaces before applying seam tape. The FLASHING TAPE shall be securely bonded to the deck sheet along the previously marked bottom sheet. The flashing shall be formed from side to side to insure a minimum of 2″ overlap of the flashing beyond any edge piece. The release paper shall be carefully removed without disturbing the placement of the flashing or deck sheet. The lap joint shall be “walked in” to fix placement and thoroughly rolled with a 2″ metal roller in the direction perpendicular to the length of the joint. This is 1 case, 2 – 6″ x 100′ rolls case, and weighs 61 lbs per case Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, PayPal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Powered by eBay Turbo Lister The free listing tool. List your items fast and easy and manage your active items. Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable. Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricing We currently only ship to the lower 48 sates, not Alaska or Hawaii
12 cases – 6″ x 100′ rolls EPDM Rubber Flashing tape P-S BY THE LOTTES COMPANIES
Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” 12 cases – 2 rolls 6″ x 100′ rolls/case, 24 rolls of vulcanized butyl flashing tape used to seal flash around roof top detail projections overlapping pieces of EPDM deck sheet roofing to form a watertight seal. Need to use primer activator to prime the seam area before applying the 6″ flashing tape. SELF VULCANIZING FLASHING JOINTS All FLASHING DETAIL: shall be sealed using 6″ OR 12″ SELF VULCANIZING FLASHING TAPE. All joints shall be shingled to shed water toward the drains, scuppers, etc. Contact surfaces for the FLASHING TAPE shall be cleaned to remove construction dirt using a light application of unleaded gas on a clean, lint-free rag. After cleaning apply primer to surfaces before applying seam tape. The FLASHING TAPE shall be securely bonded to the deck sheet along the previously marked bottom sheet. The flashing shall be formed from side to side to insure a minimum of 2″ overlap of the flashing beyond any edge piece. The release paper shall be carefully removed without disturbing the placement of the flashing or deck sheet. The lap joint shall be “walked in” to fix placement and thoroughly rolled with a 2″ metal roller in the direction perpendicular to the length of the joint. These are 12 cases, 2 – 6″ x 100′ rolls case, 24 rolls and weighs 61 lbs per case Plus freight to your location. 48 STATES Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, , Bank Wire, Paypal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number BID WITH CONFIDENCE Read my policies on my SquareTrade Seal stwithpolici Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable.Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricingWe currently only ship to the lower 48 sates, not Alaska or Hawaii
6 cases -12- 5″ x100′ rolls Cured EPDM rubber tape P & S BY THE LOTTES COMPANIES
Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” 6 cases – 2 rolls 6″ x 100′ rolls/case, 12 rolls total of vulcanized butyl COVER tape used to seal flat roof top areas, perimeter edge termination detail and other FLAT EPDM roof joints. NOT TO BE USED FOR FLASHING DETAIL! THIS PRODUCT IS COMPRISED OF CURED EPDM RUBBER LAMINATED TO UNCURED BUTYL TAPE. Need to use primer activator to prime the flat area before applying the 6″ cover tape. These are 6 cases, 2 – 6″ x 100′ rolls case, 12 rolls total and weighs 63 lbs per case Plus freight to your location. Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, , Bank Wire, Paypal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Read my policies on my SquareTrade Seal Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable.Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricingWe currently only ship to the lower 48 sates, not Alaska or Hawaii
1 Gallon Latex EPDM AND TPO RUBBER ROOFING GLUE Bonding Adhesive
Lottes Roofing 126 Point West BlvdSt. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” This is One (1) 1 Gallon pail of Latex Bonding Adgesive FREE DELIVERY 48 States Check out my other items This is latex bonding adhesive to adhere the EPDM or TPO rubber to the roofing insulation or substrate. This is a BONDING Adhesive to adhere or bond the EPDM or TPO to a substrate of wood, plywood, OSB or metal. This is NOT a seaming product that will seam EPDM to EPDM or TPO to TPO, you must use a SEAMING product like black seaming adhesive or vulcanizing seaming tape which we have available for that type of application. This is a latex based single surface bonding adhesive with coverage about 70-100 square feet per 1 gallon pail on a SINGLE surface. This adhesive is a SINGLE surface laminate adhesive that is NOT to be used in a WET condition. Allow the adhesive time to “Tack” off, which usually about 5 minutes or so. DO NOT ALLOW the adhesive to become dry before you lay in the roofing membrane. APPLY roofing membrane while the adhesive is NOT DRY BUT TACKY. Method of Applying EPDM with heavy bodied latex bonding adhesive and 3” seam tape application as required.· 1 Clean the roof surface of all shingle debris and nails. Re-fasten any loose roof boards.· 2 Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8″ without risk of possible adhesion issues.· 3 Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane· 4 Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Allow the adhesive a few minutes to “tack off” Slowly fold the EPDM roofing membrane back into place while the adhesive is still TACKY or MOIST NOT wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane.· 5 Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3”seam tape if required to splice 2 pieces of EPDM deck sheet together.· 6 Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof.Seam tape application if required to join 2 sheets together•Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet.•Clean and/or prime the seam area of both rubber sheets using FastSeam EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area•Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2″ out from the edges of the bottom sheet.•Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam.•With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape.•Remove the paper backing by pulling out from under the top sheet at a 45º angle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. Summary of My Selling PoliciesPaymentAll Credit Cards, Company Certified Checks, Bank Checks, , Bank Wire, PaypalFeesNo sales taxes UNLESS in specific states localsShippingUS and InternationalDelivery24-48 hours to ship the liner NORMALLY on in stock items, not counting weekends or holidaysRefunds & ReturnsReturns accepted on qualified items with RGA return numberContact Me BID WITH CONFIDENCE Read my policies on my SquareTrade Seal Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item negotiated between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items. Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable. Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricing We currently only ship to the lower 48 sates, not Alaska or Hawaii
10′ x 20′ WHITE 60 MIL EPDM RUBBER ROOF KIT W/ADHESIVE, 4″ X 25′ TAPE, 2 CAULK
Lottes Roofing St. Charles, MO 63303 We will work with you to give you the best deal on your EPDM, TPO, Modified Bitumen, Roof Coatings, Insulation and Roof accessory items!! Call or Email us TODAY!!! “Over 30 years experience in single ply flat roofing products!” Click Below for Certification, Qualification and Reference Data Click Here for Lottes Roofing InformationResidential and RV Division 1-888-666-9157. COMMERCIAL 1-888-895-4465 This 10′ x 20′ 60 Mil EPDM WHITE rubber roofing weighing 80 lbs Includes the Adhesive! DELIVERED FREE IN THE 48 STATES Method of Applying EPDM with heavy bodied latex bonding adhesive and 3” seam tape application as required.· 1 Clean the roof surface of all debris and nails. Re-fasten any loose roof boards. 2 Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8″ without risk of possible adhesion issues. · 3 Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane· 4 Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Allow the adhesive to tack off. Slowly fold the EPDM roofing membrane back into place while the adhesive is still wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane. · 5 Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3” seam tape if required to splice 2 pieces of EPDM deck sheet together. · 6 Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof. Seam tape application if required to join 2 sheets together • Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet. • Clean and/or prime the seam area of both rubber sheets using EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area • Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2″ out from the edges of the bottom sheet. • Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam. • With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape. • Remove the paper backing by pulling out from under the top sheet at a 45º angle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. We have latex bonding adhesive in 2 -1 gal pails that ARE INCLUDED to adhere the EPDM rubber to the roofing insulation or substrate. These bonding adhesives have a coverage of about 100-120 square feet per 1 gallon pail as a ONE SURFACE WET APPLIED LAMINATE. We also include WHITE Caulking (2 tubes)and WHITE Flashing Tape (4″ x 25′ WHITE tape) for details. We have many other accessories that you may need. No need to pay for items you do not have a reason to use. Contact us and we will assure you the products that you need are included with your order!Residential and RV Division 1-888-666-9157. COMMERCIAL 1-888-895-4465 With our professional freight forwarders we can ship our products ANYWHERE in the WORLD!! Call for your export shipping rate!! Check out my other items! When buying EPDM rubber roofing you also need to purchase the proper accessories from us to insure a proper and complete roof installation. We have listed all our EPDM accessories in our EBay store. 200 page Specification & Installation guideline online manual available at Lottes Roofing Specs Page Roof Installation Videos Our Technicians can design and determine what you need for your roofing project and give you a complete estimate for your materials as well as instruct you about your installation process!! We have both WHITE and BLACK EPDM rubber roofing. Main Distribution Facility Located in St. Charles, MO EPDM is extremely flexible, much like a tire innertube, and extremely strong. EPDM has over 350% elongation, and it’s performance characteristics are stable in temperature ranges from -50 to 240 degrees Fahrenheit before failure. The EPDM membrane also exhibits over 1,300 lbs psi tensile strength, and 150 psi tear strength. Though there are other types of roofing membrane material in the marketplace today, none of them meet all the positive characteristics, ease of handling, and price of EPDM. FORMULATION COLOR SPECIAL APPROVALSANJ45B & ANJ60B MIL EPDM BLACK UL CLASS A FM CLASS 1 ANJ60W 60 MIL EPDM WHITE UL CLASS A FM CLASS 1 PHYSICAL PROPERTIES ASTM TEST METHOD RESULTS WIDTH, INCHES D751 -0 / +2.0 LENGTH, INCHES D751 -0 / +6.0 THICKNESS, INCHES D751 +10% TENSIL STRENGTH, MIN PSI D412 D1E C 1305 ELONGATION, ULTIMATE MIN. % D412 300 TEAR RESISTANCE, MIN., LBS./INCH D624 DIE C 150 LINEAR DIMENSIONAL CHANGE, MAX. % (168 HOURS AT 2400 DEGREES F) D1204 +2 BRITTLENESS POINT AT -49 DEGREES F D2137 DOES NOT BREAK OZONE RESISTANCE (168 HOURS / 100 PPHM/1040 F/400 C/505 EXT.) D1149 NO CRACKS AT 7X MAGNIFICATION WATER ABSORBSION, MAX. % (168 HOURS AT 15 DEGREES F/70 C) D471 +8 / -2.0 HEAT AGING (28 DAYS AT 240 DEGREES F) PIN HOLES NO HOLES, COMETS, OR FISH EYES MORE THAN 1/3 DEPTH OF TOTAL THICKNESS SEAMS 2″ MIN. OVERLAP SEAM PEEL STRENGTH 2 INCH / MIN. CROSSHEAD SPEED 15 PLI MIN. SEAM SHEAR STRENGTH 2 INCH / MIN. CROSSHEAD SPEED (BREAK MUST BE MEMBRANE NOT SEAM 30 PLI MIN.) Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Money Orders, Bank Wire, Paypal Fees Depends on state Shipping US and International Delivery 24-48 hours before shipping on in stock items not counting weekends or holidays, 3-7 days NORMALLY in shipping time not counting weekends or holidays in 48 states Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me Residential and RV Division 1-888-666-9157. COMMERCIAL 1-888-895-4465 BID WITH CONFIDENCE Read my policies on my SquareTrade Seal stwithpolicies Please be prepared to unload the product from the delivery vehicle. Items less than 150 lbs will be shipped UPS or Fed Ex and will deliver directly to your door. Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item negotiated between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items. UNLESS NOTED OTHERWISE FREIGHT AND DELIVERY CHARGES ARE ADDITIONAL. PLEASE CONTACT US SO WE MAY PROVIDE YOU WITH A DELIVERY FREIGHT QUOTE
4″ x 50′ 35 Mil BLACK Flashing and Cover repair tape
Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” FBA Black 4″ x 50′ 35 mil P&S Flashing & Cover Tape Roof BITE tapes were designed by PARR Technologies as a one part solution for roof repairs, seaming, flashing, cover, RV repairs and general waterproofing applications. This innovative line of products were designed for both commercial and residential roofing applications as a single step solution for long term success. Formulated by PARR for long life cycles, these products will increase the energy efficiency of your roof system. Unlike competitors’ materials, PARR’s adhesive will not oxidize over time, crack or harden. It is a flexible seal that will adjust with the natural movements of your roofing and building system. A light mineral spirit can be used to ensure a contaminant free surface. Freight Class 55 “non-hazard”. Shelf Life 5 Years Color Adhesive – Gray (will not stain surfaces.) STEP 1: Surface must be clean and dry, moisture, dust, dirt and other foreign matter should be removed before use of project. STEP 2: Cut to length. STEP 3: Remove release liner. STEP 4: Apply using even pressure across the width of the product forcing bond between surfaces. STEP 5: Smooth out all air bubbles. For extreme bubbles, with a razor, create a small puncture and apply weight or pressure over the bubble. The BITE compound will reseal itself. We used a unique blend of our butyl technology and blended it with our proprietary block co-polymer synthetics to create a wide temperature application range adhesive that will adhere on wet surfaces at temperatures below 0ºF, while maintaining their thermal stability at temperatures up to 300ºF. Having difficulty adhering to some surfaces? No problem for PARR, being a lab driven manufacture we had the wide variety of surfaces and other adhesives you might come into contact with in mind. This proprietary adhesive blend will not allow for plasticizer migration like other butyls when in prolonged contact with TPO, EPDM, Asphalt and Coal Tar BURs, CPE and Vinyls. Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, PayPal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable. Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricing We currently only ship to the lower 48 sates, not Alaska or Hawaii
1 Roll 9″ x 100′ WHITE Cured EPDM rubber tape P & S BY THE LOTTES COMPANIES
Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” This is a WHITE 9″ x 100′ roll of COVER TAPE White 9″ x 100′ Self Adhering 60 mil CURED EPDM RUBBER Cover tape for EPDM, TPO, PVC and rubber roof 2/3 DAY USPS PRIORITY SHIPP Used to repair WHITE EPDM, TPO and PVC Roofs, 10 times STRONGER than regular P & S Flashing Self Adhering WHITE CURED EPDM with WHITE tape laminate to permanently form a watertight seal Used For roof edge Terminations, RVs, Mobile Homes, and Roof Gutter edge seal SHIPS USPS==FREE DELIVERY 48 STATES Product description 10 YEAR FULL REPLACEMENT WARRANTY TECHNICAL DATA SHEET WHITE Tapes SCOPE: This specification covers butyl adhesives with and without an Elastomeric mechanical protective carrier. DESCRIPTION: A cross-linked, re-enforced, water & UV resistant butyl adhesive can take 40 degrees below 0 to 180 degrees Fahrenheit. PROPERTY:TESTSPECIFICATIONS LIMITSMETHOD Dimension visual (per customer requirements) conformance +- 5% of dimension is standard Thickness White Cover Adhesive .030” Cover .030” Total .060” Sheer strength ASTM D 81615lb. PSI min (1) Peel strength ASTM D 4133 PLI min (1) Tensile strength ASTM D 41250 PSI max (2) Elongation ASTM D 412500% min(2) Penetration ASTM D 21740/120 MM (3) Flash Point ASTM D 92350 F min Low temperature ASTM D 746minus 49 F flexibility 1.Testing done with adhesive adhered on both sides to smooth EPDM and TPO membrane; cleaned with quick clean splice cleaner. Samples aged for 24 hours @ 70 C prior to testing. Instron speed 10”/min. 2.Specimen cut with an ASTM die C or die D. Sample pulled a 10”/min and aged at 70 C for 72 hours. 3.300-gram cone load used. SPECS: Width & Lengths may vary slightly, but within specification limits. Cover tapes 0.035” +- .005” butyl sealer thickness. NOTE: TECHNICAL INFORMATION AND DATA SHOULD BE CONSIDERED REPRESENTATIVE OR TYPICAL ONLY AND SHOULD NOT BE USED FOR SPECIFICATION PURPOSES. User’s Responsibility This Product Information cannot cover all possible situations, which the user may experience during processing. Each aspect of your operations should be examined to determine if, or where, additional precautions may me necessary. All health and safety information contained in this bulletin should be provided to your employees or customers. Main Distribution Facility Located in St Charles, MO Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Bank Wire, Paypal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY onin stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Read my policies on my SquareTrade Seal Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable. Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricing We currently only ship to the lower 48 sates, not Alaska or Hawaii
12 cases – 3″ x100′ 4- rolls/case ROOFING seaming tape BY THE LOTTES COMPANIES
Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” 12 cases of 4- 3″ x 100′ rolls, 48 rolls, of vulcanized butyl seam tape used to joint 2 overlapping pieces of EPDM deck sheet roofing to form a watertight seal. Need to use primer activator to prime the seam area before applying the 3″ seam tape. SELF VULCANIZING LAP JOINTS All lap joints: shall be sealed using RUBBER TO RUBBER TAPE. All lap joints shall be shingled to shed water toward the drains, scuppers, etc. Contact surfaces for the RUBBER TO RUBBER TAPE shall be cleaned to remove construction dirt using a light application of unleaded gas on a clean, lint-free rag. After cleaning apply primer to surfaces before applying seam tape. The RUBBER TO RUBBER TAPE shall be securely bonded to the bottom deck sheet along the previously mark proper edge alignment of the seam tape on the bottom sheet. The top sheet shall then be lapped onto the lower sheet. The release paper shall be carefully removed without disturbing the placement of either sheet. The lap joint shall be “walked in” to fix placement and thoroughly rolled with a 2″ metal roller in the direction perpendicular to the length of the joint. This 12 cases of 4 -3″ x 100′ rolls (case) are 350bs and is plus freight to your location. B. SELF VULCANIZING LAP JOINTS All lap joints: shall be sealed using RUBBER TO RUBBER TAPE. All lap joints shall be shingled to shed water toward the drains, scuppers, etc. Contact surfaces for the RUBBER TO RUBBER TAPE shall be cleaned to remove construction dirt using a light application of unleaded gas on a clean, lint-free rag. After cleaning apply primer to surfaces before applying seam tape. The RUBBER TO RUBBER TAPE shall be securely bonded to the bottom deck sheet along the previously mark proper edge alignment of the seam tape on the bottom sheet. The top sheet shall then be lapped onto the lower sheet. The release paper shall be carefully removed without disturbing the placement of either sheet. The lap joint shall be “walked in” to fix placement and thoroughly rolled with a 2″ metal roller in the direction perpendicular to the length of the joint. Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, , Bank Wire, Paypal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Read my policies on my SquareTrade Seal Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable.Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricingWe currently only ship to the lower 48 sates, not Alaska or Hawaii
1 roll 6″ x 20′ EPDM Black Roofing UNCURED FLASHING tape for repairs, RV, home
Lottes Roofing 126 Point West Blvd St. Charles, MO 63303 “Over 30 years experience in single ply flat roofing products!” Product descriptionBlack 6″ x 20′ 60 mil EPDM P&S UNCURED RUBBER Cover Tape, 2/3 DAY USPS PRIORITY SHIPPING10 Year warrantySTRONGER than regular P & S FlashingInstallation Videos http://www.lottesroofing.com/roofingvideos.html Vulcanized butyl UNCURED FLASHING tape used to seal on flat EPDM roofing areas. THIS IS FLASHING TAPE! This product is uncured butyl seam tape laminated to UNCURED EPDM deck sheet for use on flat roofing areas like perimeter metal edge strip, ROOF PENETRATION FLASHING DETAILS and to repair cut EPDM deck sheets. Main Distribution Facility Located in St Charles, MO Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, , Bank Wire, Paypal Fees No sales taxes except in applicable states Shipping US and International Delivery 24-48 hours to ship NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me BID WITH CONFIDENCE Just a note. FREE shipping is ONLY to the lower US 48 states. All other locations will have additional freight, fees, and charges as well as any and all International customs and duties as applicable.Contact us for Volume DiscountsBuy 3 items get 5% EXTRA Discount off items pricingBuy 5 items get 8% EXTRA Discount off items pricingWe currently only ship to the lower 48 sates, not Alaska or Hawaii